Thinking about building or buying a new home? You might have heard the phrase energy efficient home and wondered what it really takes to earn that label. The rules have changed. Since NCC 2022, new homes need to meet a minimum thermal performance equivalent to seven NatHERS stars, plus an annual energy use budget. That budget covers heating and cooling, hot water, lighting, pool and spa pumps, and onsite renewables like rooftop solar. But seven stars is not the whole story.
In this guide, we will unpack what an energy efficient home actually means, explain NCC 2022 and the seven star minimum, and translate NatHERS into plain language. You will also learn what stars do and do not tell you, why your climate changes the design, the practical measures to expect, how compliance is demonstrated, and when to bring in a designer or energy assessor. No jargon overload. Just clear, practical steps for beginners.

What an Energy Efficient Home Actually Means
An energy efficient home is designed and built to stay comfortable while using as little energy as possible. It works with its site and climate rather than relying on oversized heating and cooling to fix design problems. The Australian Building Codes Board (ABCB) now sets a minimum standard for new homes, so efficiency is a baseline, not a bonus.
Three outcomes make it concrete:
- Thermal comfort: staying comfortable through a Perth summer or a cold Wheatbelt night.
- Running cost: less energy for the same comfort, which usually means smaller bills.
- Emissions: lower demand means less carbon from the energy the home does use.
It’s a design outcome, not a single product. Orientation, glazing, shading, insulation, ventilation, thermal mass and appliance choice work together, which is why two homes with the same floor plan can perform very differently.
Since new homes must meet NCC 2022 minimums, the real question is how far above the minimum you want to go. Our guide to energy efficient design in WA covers that.
This guide focuses on new homes under NCC 2022. Existing homes and renovations follow their own assessment pathways, and funding and green loans aren’t covered here as those details weren’t sourced.
The Rules Changed: NCC 2022 and the Seven Star Minimum
The direction came in mid-2019, when Building Ministers asked the ABCB to develop stronger residential energy efficiency provisions, shaped by the Energy Ministers’ Trajectory for Low Energy Buildings. Those provisions landed in NCC 2022.
The headline change: the minimum thermal performance for new homes rose to the equivalent of seven NatHERS stars, per the ABCB’s overview of the provisions. That is a meaningful step up, so plenty of familiar designs need genuine changes rather than a paperwork tweak. For Western Australian builders, the practical effect is the same.
Scale adds context. The ABCB expects around 1.8 million new homes over the life of the regulation, split roughly 75 per cent houses and 25 per cent apartments. That’s why the change is treated as a shift in how homes are designed, not a niche rule.
For homeowners, the point is simple: this is where new homes have to land. It is not a voluntary green upgrade that only sustainability minded clients choose.
And the ABCB frames the provisions as fuel and technology neutral. The rules ask for an outcome, not a particular fuel or appliance brand, which leaves designers room to choose a sensible approach for each site.
Beyond Stars: The Annual Energy Use Budget
Here’s the part many homeowners haven’t heard about. Alongside thermal performance, NCC 2022 introduced a whole-of-home annual energy use budget. It measures how much energy the home’s systems are expected to use over a year.
The budget covers heating and cooling, hot water, artificial lighting, pool and spa pumps, and onsite renewables such as rooftop solar. It’s a whole-of-home number, not a shell score.
Think of it this way: the star rating looks mostly at the building shell and how well it resists heat gain and loss, while the energy budget looks at the whole house and the systems that run it. A well insulated home with an inefficient hot water system isn’t the free pass it once was.
Strategically, this pairs the thermal envelope with a whole-of-home view of how the house runs. That shifts design decisions from ticking thermal boxes to balancing the whole home, the same logic behind planning a kitchen renovation.
One honest limit: how the budget interacts with rooftop solar is set out in the compliance software. Confirm the treatment of solar with your assessor rather than assuming a fixed rule. Your assessor can talk you through how solar is treated for your design.
NatHERS in Plain Language
NatHERS is Australia’s national house energy rating scheme, and it runs on a simple number. Accredited software rates a home’s thermal performance on a 0 to 10 star scale, according to the ABCB. Higher scores mean a design needs less heating and cooling for its climate, and lower scores mean it needs more. Four accredited software packages currently do this work, so your assessor’s tool may differ from someone else’s, but the star language stays consistent.
NatHERS now reports annual energy use as well as a star rating, which lines it up with the whole of home thinking behind NCC 2022.
Here is the part people most often miss: NatHERS is climate specific. A rating is produced against a defined climate and a set of assumptions, so the same plan modelled in Perth and in a hotter or cooler regional climate will not score the same. That is why local building systems matter so much to the result.
So treat the rating as a design and comparison tool built by modelling, not a promise about a future bill and not a guarantee of how the home will feel in use.
What Seven Stars Does and Does Not Tell You
A seven star result is a useful comparison tool rather than a promise. It summarises the predicted thermal performance of one specific design in one specific climate, so you can weigh two options on a like for like basis.
It does not cover every appliance and plug load, it does not give you a guaranteed bill, and it cannot know how you actually live: how often windows are opened, or how a household uses zoning.
The rating measures predicted heating and cooling performance, not dollars.
Because a score belongs to one design in one climate, swapping glazing, reorienting a living area or adding deep eaves means the model should be re-run. A seven star result is not a property of the block or the suburb. It reflects decisions you can still change, so it pays to design for performance early.

Why Your Climate Changes the Design
A seven star result belongs to a climate as much as to a design. That is why the NCC uses climate zones, and why a home is assessed against the zone it sits in rather than one national figure.
The ABCB’s framing is that the mix of solutions will be different in each climate, and can even vary between homes in the same climate. So there is no universal checklist, only principles applied to a site. A home balancing hot summers and mild winters, a home facing wide temperature swings, and a home coping with sustained heat and humidity will each lean on different measures. We have not sourced site specific WA requirements, so confirm your zone and provisions with the ABCB and the WA building authority.
It follows that the same plan can score differently in a different climate, which matters if you move a design between regions or build on a block with unusual exposure. It is the thinking behind our climate responsive design for Perth. Bring climate and site into the brief early, at orientation, shading and window placement, and hitting the required performance gets cheaper.
Design Measures to Expect in a New Home
With your climate zone sorted, the measures themselves start to look familiar. What has changed is the flexibility.
More insulation options. The updated provisions allow a wider range of ways to hit the target, so designers can match insulation to your wall and roof construction instead of forcing one specification.
Reduced thermal bridging. This is the quiet one. Framing and structural elements that bypass insulation can undo good work, so the provisions push for attention to how components connect and where heat leaks around them.
Lighter roofs and walls in warmer climates. In hot regions, reflecting heat rather than absorbing it is a straightforward win, and lightweight construction with the right insulation becomes a realistic route.
Ceiling fans in warm climates. Fans move air and improve comfort at higher thermostat settings, which is why they now appear in the provisions for warmer zones. If you are weighing up mechanical against passive cooling in a hot, humid climate, our comparison of Passive House and natural ventilation walks through how each approach works.
They work as a package. Testing the response for your site beats copying another project.
How Compliance Is Actually Demonstrated
Once you’ve settled the design measures, the next question is how you prove they work. There is more than one way to show a design complies. Most new homes take the NatHERS accredited software route, which models the design and produces the star rating and annual energy use figure.
The alternatives matter when a design doesn’t fit the defaults. Deemed to Satisfy means following a set menu of acceptable provisions, straightforward but rigid. A verification method lets you demonstrate performance through an agreed calculation. A Performance Solution goes further, showing the outcome another way, which is where a well argued design can gain flexibility.
Assessments happen at design stage, so the rating follows the drawings, which is why it pays to settle layout choices early.
It asks for an outcome rather than a prescribed system, so different combinations of building fabric, hot water, lighting and rooftop solar can all reach the target.
Check assessor accreditation and fees directly with whoever you engage, as these vary. Approval pathways for outbuildings work much the same way, which is why planning approvals in regional WA come down to size and zoning.
Next Steps: When to Bring in a Designer or Energy Assessor
Whichever pathway you take, timing matters as much as the choice. Get a designer involved early. Orientation, window placement, shading and layout carry more performance weight than any single product you pick later.
Before the design is locked in, confirm your climate zone and the provisions that apply to your site.
Book the energy assessment before documentation is finished, not after. That way the result shapes the design instead of just reporting on it.
Keep a record of the rating and the exact design it applies to. A model that no longer matches the drawings won’t protect you, and substitutions on site can quietly change the outcome.
If you’re planning a new home in Western Australia, ORA is an accredited architectural practice based in Perth that designs residential projects across the Perth metro area and throughout regional WA. We publish guides like this to help clients understand the design decisions behind them.
Conclusion
So, what should you actually take away? Three things. Seven NatHERS stars is the minimum for new homes under NCC 2022. The annual energy use budget covers the whole home, including hot water, lighting and pool pumps, not just the shell. And the mix of solutions differs by climate, and can differ between homes in the same climate.
Then act in this order: confirm your climate zone, settle orientation, glazing and shading before you settle floor plan size, and commission the assessment at design stage so the result shapes the design.
Ask for the annual energy use figure, not just the star rating. That is where system choices such as hot water and onsite solar show up.
Treat costs, rebates and funding as things to verify with the relevant authority at the time you build.
Get the design decisions right first, and the efficiency follows.